
Applications
Circular knitting machines for automotive
Machines for interior linings, seat fabrics and floor mats, where abrasion resistance and colour consistency across batches decide acceptance.
Recommended machine types
What to put on the floor
These are the machine types we normally quote for automotive. Tell us the fabric weight and expected output and we narrow it to one configuration.
- Single Jersey
- Interlock
- Rib
- Single Jersey Computerized Jacquard
- Double Jersey Computerized Jacquard
- Double Jersey Jacquard (36/72 Pattern)
Machine names follow our catalogue naming. Not every model is stocked for every market — availability is confirmed with the quotation.
SPECIFICATION
Automotive fabric is specified by test cycle, not by hand feel
A seat cover or interior trim fabric spends its life under abrasion, ultraviolet light and heat. The knitting specification therefore starts from the abrasion and lightfastness targets the vehicle programme requires, then works back to gauge and density.
| Application | Typical GSM | Gauge | Diameter | Feeds | Notes |
|---|---|---|---|---|---|
| Seat cover face | 220–350 | E18–E24 | 30″–34″ | 48–72 | laminated to foam or spacer |
| Headliner | 140–220 | E24–E28 | 30″–34″ | 72–96 | light weight, low fogging |
| Door trim insert | 200–300 | E20–E24 | 30″–34″ | 48–72 | colour matched to seat |
| Spacer and 3D mesh | 280–450 | E18–E22 | 30″ | 36–54 | double-knit structure |
Most automotive knit is polyester, often including recycled content. Because the fabric is usually laminated, the knit face and the backing are specified together: a face fabric that meets abrasion on its own can still fail as a laminate if the bond is weak.
SPECIFICATION
Four automotive failures traced to the knitting floor
- Fogging from lubricant residue. Volatile lubricant on the yarn condenses on the windscreen in a hot cabin. A fogging test can fail on a fabric that meets every mechanical requirement, so specify low-fogging oil and confirm it with the test.
- Needle lines that appear only after dyeing. A slight density change in one wale is invisible on greige and obvious on a dark dyed face. Inspect greige against a light source before dyeing, not after.
- Colour mismatch between trim and seat. Two fabrics knitted on different machines and dyed in different lots will not match under showroom lighting. Fix the machine configuration and the dye lot across the interior set.
- Shrinkage in the laminating oven. Polyester relaxes at laminating temperature. If the greige is not heat-set to the right condition, the finished panel changes dimension after bonding.
QUALITY
The test package an automotive buyer expects
- Abrasion resistance — ISO 12947-2 Martindale, with the cycle count and end-point agreed per programme; seat faces commonly target 25,000–50,000 cycles.
- Fogging behaviour — DIN 75201, reported as gravimetric or reflectometric value depending on the specification.
- Lightfastness at elevated temperature — ISO 105-B06, because a cabin reaches temperatures a standard lightfastness test does not represent.
- Flammability — FMVSS 302 for interior materials in the US market; the equivalent national standard applies elsewhere.
- Lamination adhesion — ISO 2411 peel strength where the fabric is bonded to foam or spacer.
- Dimensional stability — measured after the actual laminating and heat-setting route, not after a laboratory wash.
Defects that look cosmetic on a seat face become rejection criteria once the part is cut. The fabric defect guide separates needle, sinker and yarn causes, which is the order we use before touching machine settings.
FAQ
Questions buyers ask about automotive
Which circular knitting machine is used for automotive?
The usual starting points are Single Jersey, Interlock, Rib. The final choice depends on fabric weight, required stretch and the gauge you sell, so we confirm the configuration against a fabric sample rather than a catalogue page.
What do you need from us to quote a machine for automotive?
Fabric type and weight, required gauge and cylinder diameter, expected output per shift, and the destination port. With those we return a configuration sheet with price and lead time.
What is the lead time and warranty?
Machines are built in 20–45 working days depending on model and configuration, then 20–45 days by sea freight. Machines carry a 12-month warranty from delivery; needles and spare parts follow the period stated on the invoice.
What abrasion level do automotive seat fabrics need?
It is set by the vehicle programme, not by the fabric supplier. Seat faces commonly target 25,000 to 50,000 Martindale cycles to ISO 12947-2, with the failure criterion agreed in advance. Confirm the number before specifying density.
Why does fogging matter for a knitted fabric?
Volatile residues from yarn lubricant and finishing condense on interior glass in a hot cabin. The fabric can pass abrasion and lightfastness and still fail the fogging test, so the lubricant specification belongs in the purchase order.
Can a standard circular machine make automotive fabric?
Yes for the knit face. What changes is the quality regime: tighter GSM control, greige inspection before dyeing, and a documented lamination route. A 30-inch machine at E18–E24 covers most seat and trim fabrics.
