Circular Knitting Fabric Defects: Causes and Fixes

Diagnose drop stitches, barre, needle lines, holes and spirality: cause trees, first checks and permanent fixes, ordered to find the fault fastest.

Short answer: most circular knitting defects trace to five sources, in this order of frequency — needle and sinker condition, yarn quality and tension, cam and butt wear, dial–cylinder alignment, and lint or climate. The defect’s direction tells you which to check first. Vertical and repeating along a wale means a single needle or slot; horizontal bands mean yarn, feeder or tension; random holes mean yarn or sinker damage. Diagnose by direction before you touch a setting.

Below is a defect-by-defect cause tree with the first check, the permanent fix, and the inspection interval that prevents recurrence.


Read the defect before you read the machine

DefectVisual signatureDirectionFirst check
Drop stitchSmall hole with a ladder running up the waleVertical, repeatingNeedle latch and hook condition
Needle lineFine vertical line of distorted stitchesVertical, continuousBent needle, worn sinker, damaged cylinder slot
BarréHorizontal band, lighter or darkerHorizontal, across full widthYarn lot, feeder tension, needle height
Holes (random)Isolated holes, no patternRandomYarn slubs and thick places, sinker wear
Spirality (skew)Legs or side seams twist after washingDiagonalYarn twist direction, rotation, course length
Oil marksGrey or brown streaksRandom or along feeder pathOil grade, lubrication rate, misting
GSM driftWeight changes across a rollLongitudinalYarn count variation, take-down tension

Direction is the fastest filter available: a vertical line cannot be caused by a feeder, and a horizontal band cannot be caused by one bent needle. Applying that rule first eliminates half the checklist.


Drop stitches: the needle is usually guilty

A drop stitch is a stitch that fails to form and then unravels up the wale. The machine is telling you that a specific needle failed to hold the loop at one point in the cycle.

Check in order:

  1. Latch and hook. A sticky latch, a burred hook or a needle that has lost its latch spring. Remove the needle and cycle the latch by hand — it should snap freely. Replace, do not clean and refit.
  2. Needle groove and slot. Compacted lint or dried oil in the cylinder slot prevents the butt from following the cam track. Clear the slot fully; do not push debris down into the cylinder.
  3. Yarn tension at that feeder. A single over-tight feeder produces drop stitches at one position only. Compare with a hand tensiometer across all feeders.
  4. Cam setting at that position. A cam that lifts too early releases the loop before the needle closes. This is a setting issue, not a parts issue — and it is the one cause that repeats across several needles in the same sector.

Permanent fix: replace the needle, clean the slot, verify feeder tension within the recommended band, then re-check the cam Track after 24 hours of running. If the same position drops again within a week, the cylinder slot is worn and the cylinder needs assessment.

Prevention: needle inspection on a fixed interval — commonly 500–1,000 running hours depending on gauge and yarn abrasiveness — with a full-set replacement at the point where breakage rate starts climbing.


Needle lines: a wear problem, not a yarn problem

A continuous fine vertical line means one wale is knitting at a slightly different tension from its neighbours. The cause is almost always mechanical:

  • Bent needle. Even a 0.05 mm deflection shows as a line. Roll the needle on a flat surface; any wobble means replacement.
  • Worn sinker. Sinkers control loop length. A sinker with a rounded or burred edge holds a different loop, producing a line that follows the sinker, not the needle.
  • Damaged cylinder slot. A burr in the slot changes needle path. Feel for it with a fine probe; a slot that has been damaged twice in the same place needs cylinder attention.
  • Oil or lint in one slot. Produces the same signature as a bent needle, at zero cost to fix. Clean first, then inspect.

Prevention: sinker inspection at 1,500–2,000 hours; incoming inspection of replacement needles and sinkers before they enter the machine. A batch of undersized sinkers will produce lines that no amount of setting adjustment fixes — which is why incoming gauge and hardness inspection of needles and sinkers belongs in the quality system, not in the spare-parts store.

Fine-gauge machines amplify this: at E44 and above, a marginal sinker that runs acceptably at E28 produces visible barré and lines. The 44-gauge barré elimination method covers the finer tolerances involved.


Barré: the hardest defect to attribute

Barré is a horizontal band of altered shade or texture. Because it appears across the full width, it usually originates upstream of the needles — in yarn, feed or tension — but it can also come from needle height variation across the cylinder.

Work through four suspects, cheapest first:

  1. Yarn lot change. Barré at a lot boundary is normal and unavoidable within tolerance; barré in the middle of a lot is not. Record lot numbers on the roll ticket so the correlation is visible.
  2. Feeder tension imbalance. A difference of a few grams between feeders produces a visible band. Measure all feeders with the machine running at production speed, not at idle.
  3. Yarn path and accumulation. A partially blocked tensioner or a worn accumulator changes tension cyclically — producing regular bands at a fixed interval that matches the accumulator cycle.
  4. Needle height variation. Measure needle height across the cylinder with a dial gauge. Variation beyond the machine maker’s tolerance changes loop length per wale, which reads as a subtle band after dyeing.

Prevention: feeder tension checks at every shift start, needle height audit at each needle-set replacement, and lot traceability on the roll ticket. Dyeing amplifies small irregularity — a band that is invisible in greige may be obvious after finishing, so inspect after finishing too.


Random holes: yarn quality and sinker wear

Holes with no pattern are rarely a needle problem — one bad needle makes a repeating line, not random holes.

  • Yarn thick places and slubs burst the stitch at the point of entry. Check the yarn clearing and splicing quality at winding.
  • Sinker wear nicks the yarn at the loop-forming point. Inspect sinker edges under magnification at the interval recommended for your gauge.
  • Feeder and yarn-guide damage — a grooved guide cuts filaments progressively, producing holes that increase through the shift.
  • Excessive take-down tension stretches the fabric and opens stitches, especially on open-width machines.

Prevention: yarn clearing specification agreed with the spinner, sinker inspection interval respected, guide condition checked at each maintenance stop.


Spirality and GSM drift: the process causes

Spirality (garment twist after washing) comes from twist live in the yarn, machine rotation direction and course length. It is a design-and-process issue, not a defect to be sorted out at inspection:

  • Match yarn twist direction to machine rotation for the fabric structure.
  • Keep course length within the agreed band; slack courses increase spirality.
  • Test after relaxation washing, not on greige. Standards for dimensional change after domestic washing — ISO 6330 with ISO 5077, or AATCC 135 — define the test that your buyer will use.

GSM drift across a roll points to yarn count variation or take-down tension change. Weigh three samples per roll at fixed intervals; if drift tracks the yarn lot, the fix is at incoming yarn inspection, not at the machine.


The 20-minute daily routine that prevents most of this

FrequencyTaskDefect it prevents
Shift startFeeder tension check, lint blow-downBarré, drop stitches
DailyFirst-roll inspection under light, defect log by type and positionAll
WeeklyNeedle and sinker visual scan, oil level, mist and filterNeedle lines, oil marks
500–1,000 hNeedle inspection and replacement of suspect needlesDrop stitches, needle lines
1,500–2,000 hSinker inspection and replacementHoles, needle lines
Per manualOil change, cam track inspection, cylinder/dial alignment checkBars, mechanical wear

Log defects by position and direction, not just by name. A defect log that says “hole, feeder 12, vertical” is a maintenance instruction; one that says “hole” is a complaint.


Frequently asked questions

What causes drop stitches on a circular knitting machine? A needle that fails to hold the loop: sticky or broken latch, burred hook, lint in the cylinder slot, over-tight feeder tension, or a cam releasing the loop too early. Check the needle first, then the slot, then feeder tension, then cam timing.

What is the difference between a needle line and barré? A needle line runs vertically along one wale and points to a single needle, sinker or slot. Barré runs horizontally across the full width and points to yarn, feeder tension or needle height variation.

Why do holes appear only in some rolls? Usually yarn quality — thick places, slubs or splicing faults — or a feeder guide that has started to groove. Random holes rarely come from needles, which produce repeating vertical faults instead.

How often should needles be replaced? Inspect at 500–1,000 running hours depending on gauge and yarn abrasiveness, and replace on condition rather than on a fixed calendar. Track breakage rate: a rising trend means the set is at end of life.

Can barré be fixed after dyeing? No. Barré is set in the greige fabric; dyeing only makes it visible. Prevention is feeder tension control, yarn lot management and needle height consistency.

How do I test for spirality correctly? After relaxation washing per ISO 6330 with dimensional change measured per ISO 5077, or AATCC 135 for the US market. Measuring on greige fabric understates the problem.

What oil grade should I use? The grade the machine maker specifies — typically an ISO VG grade matched to the lubrication system, with the needle oil kept separate from gearbox oil. Using a heavier oil to “reduce consumption” causes misting and oil marks. See the lubrication guide for the selection logic.


Fix the cause, then fix the repeat

Every defect above has a cheap first check and an expensive permanent fix. Start with the direction rule, confirm with measurement, and close the loop by recording the position. If the same defect returns within a month at the same position, the component is worn rather than mis-set — replace it, and check the batch it came from.

For the component-level detail behind these fixes, see the cam types and maintenance guide and the needle size reference. Yarn-breakage stops that are not defects but stop-motion faults are covered separately in the yarn breakage troubleshooting guide. Replacement needles, sinkers, cams and belts are listed in our circular knitting spare parts range.

Test standards referenced: ISO 6330 (domestic washing procedures), ISO 5077 (dimensional change), AATCC 135 (dimensional change of fabrics), ISO 12947-2 (Martindale abrasion), ASTM D3786 (bursting strength). Confirm editions and the buyer’s protocol before writing them into a specification.

Leave a Reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.

ES